Eject-Ease

Mold Release for Thermoplastics

Description:
KadKlad Eject - Ease is a quick-cure, spray-on, semi-permanent mold release for thermoplastics manufacturing. Eject - Ease provides multiple releases without material transfer, pre-release, or build-up.

Uses:
Eject - Ease can be used with most resins and all major thermoplastic forming methods including Rotational Molding, Thermo/Vacuum Forming, Injection Molding and Blow Molding.

Polymer Structure:
Eject - Ease is delivered in a resin solution based on the Kadko family of polymers. Unique chemical reactions produce polysilazane polymers that are parallel in structure to silicone resins. These polymers exhibit easy cure by cross-linking at room temperature and extraordinary adhesion to almost all substrates.

Kadko polymers were originally developed for use in the aerospace industry where complete chemical cross-linking of the surface is necessary to prevent contamination of parts that are to be painted or bonded in later steps. This technology gives Eject - Ease extreme longevity without build-up or transfer.

Application Instructions:

Mold Preparation:
Remove all surface contaminants, resins and releases from mold surface with method appropriate to mold type. As final prep, clean surface again with KadKlad AllKleen to remove any remaining residue.

Eject - Ease can be applied with virtually any conventional sprayer that can produce an even, atomized spray. For best results apply Eject - Ease with a pressurized atomizer such as a Sure-Shot or suitable substitute using dry nitrogen as propellant.

Eject - Ease can be applied at all surface temperatures between 72° F and 300° F, with optimum application temperatures between 110° F and 220° F.

For first application, apply four medium-weight coats in an even manner, allowing each coat to fully evaporate before application of the next.

Mold can be placed into production immediately after application of final coat.

When touch up is needed re-apply two or three coats depending on production requirements.

This information is provided for professionals experienced in the application of semi-permanent solvent-based mold releases. Additional information can be accessed by contacting a KADKO representative.

Material Safety Data Sheet

Eject-Ease

Kadko, Inc. 01/05/06
P.O. Box 722
205 Bethel Ave.
Beech Grove , IN 46107
Tel: 317-788-0284 Fax: 317-788-0304

Product Code: 040203A

Section I- Nomenclature:
Chemical Name and Synonyms: Solvent-Resin Blend
Trade Name and Synonyms: Eject-Ease
Chemical Family: Polymeric Resin-Solvent Blend
Formula: Blend

Section II Hazardous Ingredients 7 Section 313 Supplier Information:
If a hazardous ingredient is identified as a toxic chemical via hazard code "A" that chemical is subject to the reporting requirements of section 313 of the emergency planning and community right to know act of 1986 and of 40CRF372.

Hazard Codes (HAZD):
C=Carcinogen
H= Hazardous (OSHA)
A= Superfund Amendments and Reauthorization Act (SARA)

Section III Physical Data:
Boiling Point (Deg.F) UNK Specific Gravity 0.79 (H 2 0=1)
Vapor Pressure (mm hg) UNK
Vapor Density (Air=1) >1
Solubility in water- Insoluble in water
Appearance and odor- Colorless, Mild Hydrocarbon odor.

Manufacturer Recommendation*

Section IV-Fire Explosion Hazard Data:
Flash Point (Deg.F) 104° F Method Used-TCC
Lower Explosion Level Unknown Upper explosion level- Unknown

Extinguishing Media:
Powder or foam recommended

Special Fire Fighting Procedures:
Self contained breathing apparatus and protective clothing should be worn in fighting fires involving chemicals;

Unusual Fire and Explosion Hazards:
None

Section V-Health Hazard Data:
Threshold limit value-See section II

Effects of overexposure:
May irritate eyes, skin, and mucous membrane of the respiratory tract. Exposure to very high concentrations may cause sensitization of the myocardium and may aggravate impaired cardiovascular functions. Excessive exposure may damage kidneys and liver. Anesthesia, nausea, dizziness.

* As recommended by the manufacture, similar chemicals can cause these effects.

Emergency and First Aid Procedures:
Inhalation-Remove to fresh air
Eyes Contact-Flush with water
Skin Contact-Wash with soap and water
Ingestion- Call a Physician.

Section VI- Reactivity Data:
Stability- Stable
Conditions to avoid-none

Incompatibility (Materials to avoid):
Oxidizing materials can cause a reaction

Hazardous Decomposition Products:
Carbon dioxide, carbon monoxide, fumes and smoke in case of incomplete combustion.

Hazardous Polymerization:
Will not occur.

Section VII- Special Protection Information:

Eye Protection:
Goggles, in case of spillage

Other Protective Equipment:
Use impervious clothing if necessary to avoid prolong skin contact.

Section VIII- Special precautions:
Precautions to be taken in storage and handling Avoid open flames and sparks. Keep container closed tightly to avoid hydrolysis of product by moisture. Storage should be in compliance with NFTA and OSHA 29CRF1910.106 And 107

Other Precautions:
None

HMIS Rating:
Health Hazard: 1
Flammability: 3
Reactivity: 0

Hazard Rating:
0 = Least
1 = Slight
2 = Moderate
3 = High
4 = Extreme

All INFORMATION AND RECOMMENDATIONS PROVIDED IN THIS MSDS, ARE CORRECT TO THE BEST OF OUR KNOWLEDGE AND ACCURATE AT THE DATE OF THE PUBLICATION.

NOTHING HEREIN IS TO BE CONSTRUED AS A WARRANTY. IT IS THE RESPONSIBILITY OF THE FINAL END USER TO DETERMINE THE APPLICABILITY OF SUCH INFORMATION OR THE SUITABILITY OF ANY PRODUCT FOR HIS OR HER OWN PARTICULAR PURPOSE.