KadKlad Mold Hardener

Extends mold life---Cures to a hard film that protects the mold surface. This keeps the Mold in production longer.

Easy to apply---No special tools or procedures needed. Flows and levels quickly with a cotton cloth.

Has a forgiving work time---Kadklad has a broad range of buff time, working around you instead of you working around it. You can achieve the same results in one minute or five, all with the same ease.

Gives new life to old molds---Extremely worn molds achieve a new life thanks to the hardness of Kadklad Mold Hardener. It cures hard with a gloss finish.

Allows new molds to run in production hassle free---Green molds tend to have a break in time before you get that seasoned effect. Kadklad Mold Hardener spares you that break –in time.

We offer technical assistance to ensure your special needs are met.---All operations are not the same, all molds are not the same. We realize this and will work with you to achieve the best possible results.

Application Instructions

Surface Preparation:
The mold should be free of dirt, wax, oil, or any other foreign material. We recommend using 3M Finesse-it Part No -05928 mild grit compound to cut any previous releases, or wax coatings from the manufacturer off. Then use Kadko AllKleen after compounding to remove all contaminants from surface.

Application:
Apply a liberal amount of material to applicator cloth to create a nice wet film. Coat an area of convenient size (2-3 sq. ft.) and let stand approximately 3-5 min. Buff to high gloss using a soft, clean, dry, natural white, 100% cotton cloth. When starting a new area, reapply more sealer to the applicator cloth and overlap slightly as each new section is done. Continue in this fashion until the entire surface is covered. Two coats will ensure that any areas inadvertently missed the first time are coated with sealer. Allow a minimum of 10 minutes between coatings. If used on a green or unseasoned mold add one additional coating until you get a seasoned effect to your mold. Release agents can be applied immediately after last application of sealer.

Application Tips:

• Use only all natural un-dyed 100% cotton cloths to prevent leaching of colors onto mold surface.

• If release is left too long in place before buffing and staining appears, rewet surface with sealer, wait 2-5 minutes, and buff.

• This is a room temperature curing system; this material should not be applied hot molds.

Material Safety Data Sheet

KadKlad Mold Hardener

Kadko, Inc. 01/05/06
P.O. Box 722
205 Bethel Ave.
Beech Grove , IN 46107
Tel: 317-788-0284 Fax: 317-788-0304

Section I- Nomenclature:
Chemical Name and Synonyms: Solvent-Resin Blend
Trade Name and Synonyms: KADKLAD Mold Hardener
Chemical Family: Polymeric Resin-Solvent Blend
Formula: Blend

Section II Hazardous Ingredients 7 Section 313 Supplier Information:
If a hazardous ingredient is identified as a toxic chemical via hazard code “A” that chemical is subject to the reporting requirements of section 313 of the emergency planning and community right to know act of 1986 and of 40CRF372.

Hazard Codes (HAZD):
C=Carcinogen
H= Hazardous (OSHA)
A= Superfund Amendments and Reauthorization Act (SARA)

Section III Physical Data:
Boiling Point (Deg.F) UNK Specific Gravity 0.79 (H 2 0=1)
Vapor Pressure (mm hg) UNK
Vapor Density (Air=1) >1
Solubility in water- Insoluble in water
Appearance and odor- Colorless, Mild Hydrocarbon odor.

Section IV-Fire Explosion Hazard Data:
Flash Point (Deg.F) 35 ° F Method Used-TCC
Lower Explosion Level Unknown Upper explosion level- Unknown

Special Fire Fighting Procedures:
Self contained breathing apparatus and protective clothing should be worn in fighting fires involving chemicals;

Effects of overexposure:
May irritate eyes, skin, and mucous membrane of the respiratory tract. Exposure to very high concentrations may cause sensitization of the myocardium and may aggravate impaired cardiovascular functions. Excessive exposure may damage kidneys and liver. Anesthesia, nausea, dizziness.

Emergency and First Aid Procedures:
Inhalation-Remove to fresh air
Eyes Contact-Flush with water
Skin Contact-Wash with soap and water
Ingestion- Call a Physician.

Incompatibility (Materials to avoid):
Oxidizing materials can cause a reaction

Hazardous Decomposition Products:
Carbon dioxide, carbon monoxide, fumes and smoke in case of incomplete combustion.

Other Protective Equipment:
Use impervious clothing if necessary to avoid prolong skin contact.

Section VIII- Special precautions:
Precautions to be taken in storage and handling Avoid open flames and sparks. Keep container closed tightly to avoid hydrolysis of product by moisture. Storage should be in compliance with NFTA and OSHA 29CRF1910.106 And 107

All INFORMATION AND RECOMMENDATIONS PROVIDED IN THIS MSDS, ARE CORRECT TO THE BEST OF OUR KNOWLEDGE AND ACCURATE AT THE DATE OF THE PUBLICATION.

NOTHING HEREIN IS TO BE CONSTRUED AS A WARRANTY. IT IS THE RESPONSIBILITY OF THE FINAL END USER TO DETERMINE THE APPLICABILITY OF SUCH INFORMATION OR THE SUITABILITY OF ANY PRODUCT FOR HIS OR HER OWN PARTICULAR PURPOSE.

Hazardous Material	% by Wt.	TLV Meas.	PEL Meas.	CAS NBR	HAZD
Isopropyl Acetate	5-10%		250ppm	108-21-4	H
Isoparaffnic Hydrocarbon	60-75%		400ppm*	64741-66-8	H
Acetate ester C9-11 Alcohol Branched Boiling-428F-482F	1-5%		50ppm	108419-34-7